Software-update: Cura 5.7.0 bèta 1
Cura is ontwikkeld door UltiMaker om 3d-printen zo gemakkelijk en gestroomlijnd mogelijk te maken. Cura bevat alles wat je nodig hebt om een 3d-bestand te kunnen printen. Het werkt met alle UltiMaker-printers, maar ook met die van RepRap en Printrbot. Cura laat zich gemakkelijk installeren en bevat zowel de laatste firmware als de kalibratiebestanden voor de 3d-printer. De eerste bètarelease van Cura versie 5.7.0 is uitgekomen en hierin zijn de volgende veranderingen en verbeteringen aangebracht:
Universal Cura Project filesUniversal Cura Project files contain models and settings and can be shared with people who have different printers. They can be used on any printer and they allow you to include positional data for the models on your build plate as well as select settings. Visit our Thingiverse page to download this amazing Dinosaur SD Card Holder to try the ease of sharing settings yourself.
Newly introduced SettingsSettings that define the raft offset for top, middle and bottom raft layersBrim only on the inside setting, resolves #2853Introduced a new Prime tower type: Interleaved, next to the current NormalApply Monotonic ordering to the Raft Top SurfaceRaft Wall Line Count for the Bottom, Middle, and Top of the raftAllowing to define print sequence manually
Settings that define the raft offset for top, middle and bottom raft layersBrim only on the inside setting, resolves #2853Introduced a new Prime tower type: Interleaved, next to the current NormalApply Monotonic ordering to the Raft Top SurfaceRaft Wall Line Count for the Bottom, Middle, and Top of the raftAllowing to define print sequence manuallyMethodX and MethodXL specific improvementsEnabled Print over Cloud for UltiMaker MethodX and Method XL printersIntroduced ASA, SR30, and Nylon12-CF profiles for MethodX and Method XL PrintersImproved the predicted printing time so it's closer to the actual printing time on the MethodX and MethodXLImproved the idle nozzle temperature for dual extrusion printing on MethodX and MethodXLResolved a crash for the Method printer when navigating to the Monitor tabImproved the way that the fanspeeds were listed and controlled for MethodX and MethodXL printersUpdated Raft settings for UltiMaker MethodX and MethodXLEnabled Monotonic Raft Surface to improve adhesionIncreased the Minimum Retract Distance to improve infill pattern wall overlaps
Enabled Print over Cloud for UltiMaker MethodX and Method XL printersIntroduced ASA, SR30, and Nylon12-CF profiles for MethodX and Method XL PrintersImproved the predicted printing time so it's closer to the actual printing time on the MethodX and MethodXLImproved the idle nozzle temperature for dual extrusion printing on MethodX and MethodXLResolved a crash for the Method printer when navigating to the Monitor tabImproved the way that the fanspeeds were listed and controlled for MethodX and MethodXL printersUpdated Raft settings for UltiMaker MethodX and MethodXLEnabled Monotonic Raft Surface to improve adhesionIncreased the Minimum Retract Distance to improve infill pattern wall overlapsThe new materials for the Method Series only become available with a firmware update. Currently, the firmware that supports the new materials on the Method series is not available yet. We are working hard to make it available as soon as possible.
Other improvementsIntroduced an analyzing tool in the cura engine to better track slicing crashes, and started fixing the biggest reports coming in.The play speed of the nozzle in the preview is now closer to the movement of the printheadIntroduced an option to choose Drop Model to Buildplate every time a project file is loadedIntroduced DisplayInfoOnLCD Post Processing Script which combines DisplayFilenameAndLayerOnLCD with DisplayProgressIntroduced alternative camera navigation similar to FreeCAD Trackpad
Introduced an analyzing tool in the cura engine to better track slicing crashes, and started fixing the biggest reports coming in.The play speed of the nozzle in the preview is now closer to the movement of the printheadIntroduced an option to choose Drop Model to Buildplate every time a project file is loadedIntroduced DisplayInfoOnLCD Post Processing Script which combines DisplayFilenameAndLayerOnLCD with DisplayProgressIntroduced alternative camera navigation similar to FreeCAD TrackpadResolved significantly slower slicing for models with a lot of holesA significant amount of crashes have been resolved that are caused by self intersecting polygonsAlign to Buildplate did not work for grouped meshes, resolves #14237The models in a 3mf file would not load in their saved position, please note that this also changes the behavior of the "import models" feature of a 3mf file, for this feature the saved model location will be ignoredReduced the amount of floating support in areas near the support overhang angle thresholdFixed a bug with the Initial Extruder Number in the start gcode, resolves #17501Fixed a bug where Z could be negative if Remove Empty Layers was enabled, resolves #15975Pressing the Esc key now doesn't exiting full screen modeImproved the OAuth protocol to improve signing in with plug-insFixed tree support-related crashes if there are no overhangsFixed some slicing crashes with tree supportFixed available height when adding modifier mesh in One at a Time printingImproved behavior for loading 3mfs by giving the models original namesAdded an error so LimitXYAccelJerk doesn't run unless Accel Control is enabled in CuraSome helpful code cleanup
Resolved significantly slower slicing for models with a lot of holesA significant amount of crashes have been resolved that are caused by self intersecting polygonsAlign to Buildplate did not work for grouped meshes, resolves #14237The models in a 3mf file would not load in their saved position, please note that this also changes the behavior of the "import models" feature of a 3mf file, for this feature the saved model location will be ignoredReduced the amount of floating support in areas near the support overhang angle thresholdFixed a bug with the Initial Extruder Number in the start gcode, resolves #17501Fixed a bug where Z could be negative if Remove Empty Layers was enabled, resolves #15975Pressing the Esc key now doesn't exiting full screen modeImproved the OAuth protocol to improve signing in with plug-insFixed tree support-related crashes if there are no overhangsFixed some slicing crashes with tree supportFixed available height when adding modifier mesh in One at a Time printingImproved behavior for loading 3mfs by giving the models original namesAdded an error so LimitXYAccelJerk doesn't run unless Accel Control is enabled in CuraSome helpful code cleanupIntroduced high-speed profiles for the layer heights <0.15mm for Ultimaker PLA, T-PLA, ABS and PETG.Updated Initial Layer Speed settings for UltiMaker S3, and UltiMaker S5Updated the Shrinkage Factor for PET CF to improve dimensional accuracyImproved self-support settings for UltiMaker MaterialsRenamed UltiMaker PP Transparent to UltiMaker PP NaturalIncreased part strengths of high-speed modes by compensating for slip in high flow ratesImproved adhesion settings for UltiMaker ABS
Introduced high-speed profiles for the layer heights <0.15mm for Ultimaker PLA, T-PLA, ABS and PETG.Updated Initial Layer Speed settings for UltiMaker S3, and UltiMaker S5Updated the Shrinkage Factor for PET CF to improve dimensional accuracyImproved self-support settings for UltiMaker MaterialsRenamed UltiMaker PP Transparent to UltiMaker PP NaturalIncreased part strengths of high-speed modes by compensating for slip in high flow ratesImproved adhesion settings for UltiMaker ABSIntroduced Elegoo Neptune 4 Plus and Max, and updated Elegoo Neptune 4 and ProIntroduced Anycubic Kobra 2 Printer DefinitionIntroduced Flying Bear Ghost 6Introduced Creality Ender 3 V2 NeoIntroduced Dagoma Sigma Pro 500z, and Dagoma Sigma Pro 500z DualIntroduced RRatRig V-Core 3, 200mm, 300mm, 400mm, 500mm and RatRig V-MinionIntroduced Flashforge Adventurer 3 (AD3 / AD3C / AD3 Lite / AD3 Pro) & Adventurer AD4, and AD4 LiteUpdated the dimensions for Ender 3 V3 SUpdated start Gcode for creality_ender3v3se & Anycubic Kobra Go/Kobra 2Updated print and retraction settings for Sovol 3D printersUpdated Creality Ender 5 Plus Bed Leveling CommandUpdated Voron definition to support Voron/Klipper
Introduced Elegoo Neptune 4 Plus and Max, and updated Elegoo Neptune 4 and ProIntroduced Anycubic Kobra 2 Printer DefinitionIntroduced Flying Bear Ghost 6Introduced Creality Ender 3 V2 NeoIntroduced Dagoma Sigma Pro 500z, and Dagoma Sigma Pro 500z DualIntroduced RRatRig V-Core 3, 200mm, 300mm, 400mm, 500mm and RatRig V-MinionIntroduced Flashforge Adventurer 3 (AD3 / AD3C / AD3 Lite / AD3 Pro) & Adventurer AD4, and AD4 LiteUpdated the dimensions for Ender 3 V3 SUpdated start Gcode for creality_ender3v3se & Anycubic Kobra Go/Kobra 2Updated print and retraction settings for Sovol 3D printersUpdated Creality Ender 5 Plus Bed Leveling CommandUpdated Voron definition to support Voron/Klipper
Source:
Tweakers.net